Handling Instructions For Flexible Intermediate Bulk Containers

STORAGE OF EMPTY FIBCs
Empty FIBCs and liners should be kept clean and stored undercover in such a manner that accidental damage, exposure to sunlight and extreme climatic conditions are avoided.
FILLING FIBCs

FIBCs are preferably filled with the base of the bag supported by the ground or a pallet, and the body of the bag supported by the top lift device.
If the FIBC has a discharge spout, it should be tied off or closed before filling.

STABILITY OF FILLED FIBCs
When filled, the ratio of the height of the bag to the width/diameter of the bag should not be more then 2:1. Stability of bags may be improved by vibration during or after filling.
LIFTING FIBCs
When lifting FIBCs with a fork lift truck, be sure that the fork lift tines are spaced correctly. All lifting loops, sleeves, or other lifting devices should be vertical, so that no lateral forces will be created in the FIBC. Be sure that the lifting loops are not twisted. Fork lift tines should have rounded edges and/or protective covers. FIBCs should be raised or lowered smoothly.
HORIZONTAL CARRYING WITH FORK LIFT TRUCKS
The fork lift truck must be suitable for the load to be carried. When traveling with a FIBC hanging from the fork lift tines, there is a danger of the truck becoming unstable. The FIBC should be held close to the mast and as low as possible with the mast tilted slightly backwards. Make sure that the FIBC body will not be damaged by the wheels of the truck. The load should not restrict the view of the driver. FIBCs must not be dragged. The truck should be brought to a stop before the FIBC is raised or lowered.
HANDLING WITH CRANES OR HOISTS
The hooks, spreader bars or other devices used for lifting, should have rounded edges and/or protective covers. FIBCA recommends the use of safety hooks with an integrated latch to prevent the hook from accidentally slipping of the loop. Hooks should have a sufficiently large radius to prevent squeezing the loop. When the FIBC is suspended, the loops must be vertical, without any twists or knots.
RIGHTING FIBCs

To right an FIBC that has toppled on its side, an endless fabric sling, wound through all the lifting loops, should be used. Any attempt to lift the FIBC using fewer loops than those provided, may result in the loops being torn off.

EMPTYING FIBCs

FIBCs are usually emptied by gravity, but can also be emptied by suction.

When emptying by gravity trough a bottom discharge spout, the rate of discharge can be controlled by restricting the outlet. Flow can be stopped by lowering the FIBC onto the discharged load.

FIBCs with a plain/solid bottom can be emptied by cutting the base of the bag. Again, the flow can be stopped by lowering the bag onto the discharged load.

No one should stand under an FIBC during discharge.

A bottom discharge spout should be opened only when the FIBC is suspended over a safety support that will prevent injury to the operator in the event of a failure of the lifting device.

Under no circumstances should anyone stand underneath a suspended FIBC or place their arm beneath an unsupported FIBC.

STACKING OF FILLED FIBCs

When stacking filled FIBCs 2 or more high, every effort should be made to ensure that the stack is stable.

Where possible, the stack should be formed against at least 2 retaining walls, preferably 3, to achieve maximum stability. Generally, the higher the stack, the greater the number of retaining walls required. Where only free stacking is possible, a pyramid method should be used.


FIBCs should not be pushed into a stack as this can cause damage to the sides or back of the FIBC.

STORAGE OF FILLED FIBCs

If FIBCs are stored outside, attention should be paid to the top closure.

Be sure the top closure if properly tied off. FIBCs should be covered with waterproof, U.V. protected material to avoid water collecting on the top of the FIBC and to prevent damage from sunlight.

Be sure that FIBCs are not standing in water.

HAZARDOUS MATERIALS
Special care should be taken when handling bags with UN or DOT regulated materials. For questions concerning the material, refer to the supplier´s MSDS.
EXPLOSIVE MATERIALS AND AREAS
If FIBCs are to be filled or emptied in flammable or explosive atmospheres, special features such as anti-stat material should be utilized.

Do

  • Do observe the handling instructions on the label.
  • Do check that the discharge spout is closed off before filling.
  • Do ensure that the filled FIBC is stable.
  • Do close the top inlet correctly.
  • Do inflate the liner prior to filling.
  • Do take appropriate measures in regard to dust control.
  • Do use lifting gear of sufficient capacity to take the suspended load.
  • Do ensure that the edges of the fork lift tines are smooth, or protected.
  • Do adjust fork lifte tines to the correct width for the FIBC being handled.
  • Do ensure that crane hooks are of adequate
  • Do ensure that crane hooks are of adequate size and well rounded.
  • Do consider the possibility and effects of static electricity.
  • Do protect the FIBCs from rain and prolonged sunlight.
  • Do ensure that FIBCs are adequately Secured in transportation.
  • Do dispose of FIBCs in accordance with ecological requirements.

Don't

  • Don´t exceed the Safe Working Load under any circumstance
  • Don´t fill FIBCs unevenly
  • Don´t stop or start suddenly during transportation.
  • Don’t subject FIBCs to sudden lifts or stops
  • Don’t allow personnel under a suspended FIBC
  • Don’t allow the FIBC to project over the side of a vehicle or pallet.
  • Don’t tilt the mast of the fork lift forward.
  • Don’t withdraw fork lift tines prior to relieving all the load on the lifting device.
  • Don’t stack FIBCs unless sure of stability.